SAMCO Engine Cooling Kit for BMW S1000RR (2020-present)

$768.99 AUD $805.00 AUD Save $36.01 AUD

Tax includedShipping calculated at checkout

BT Moto Part No. RR-COOLINGKIT20+BK

3+ in Stock at MODE Locations!

BIG INVENTORY
MODE is Australia's Largest Retailer & Wholesaler of Performance & Aesthetic Parts & accessories for European vehicles.

Description ABOUT MODE. MODE+ Rewards

Description

BT MOTO INTAKE FLAPPER REMOVAL KIT

As many of our customers know, our IAT (Intake Air Temperature) Kit for the 10-19 BMW S1000RR has been extremely popular and shows noticeable gains on the street and even dyno.  This IAT strategy was first used by Dinan (BMW) in the 1990's.  However, the 2020 S1000RR included some serious changes and required a new strategy for this project.

New for 2020 is our Intake Flapper Removal Kit.  The 2020 S1000RR now has flappers in the intake tract, these flappers only allow a small amount of air to pass through to the engine until 6000 RPM when the flappers finally open.  When the flaps aren't open it allows for stagnant, hot air to raise IAT readings and block air flow to the engine.  Hot air and low airflow equals less power.  This is why we developed our IAT kit years ago.  The flapper removal is just an add-on progression to the new model.  From scratch we developed block off plates and a whole new IAT relocation kit (which you can find Here) as the harness has changed from the 10-19 models.  All parts fit very snug and are made from billet aluminum for weight consideration and longevity.

The new airbox "flapper" design was made to reduce engine noise at low RPM's.  Instead of the previous foam restrictor that we saw in the 17-19 models, the 2020 S1000RR almost completely closes off the airbox in certain scenarios.  This lack of airflow leads to very high intake temperatures.  The ECU's strategy is designed around this "heat soak".  Timing retard is based on a "per gear" and "per RPM" strategy and will not taper off until higher gears due to the airflow and RPM needed to open the flappers.  This is vastly different than previous years and more similar to the BMW GS1200’s (which also benefited greatly from this kind of modification).  The first half of the throttle angles (0-50% throttle, commanded) and first three gears are heavily timing retarded on the stock calibration.  This is due to hot and stagnant air that sits in the airbox while the flappers stay closed.  The design of the OEM flapper servo creates an unnecessary bottleneck of airflow inside the airbox at higher speeds.  This distributes air to the inner most cylinders, negating performance and the maximum "ram air" effect the factory airbox can provide.

Our kits have been installed and successfully tested with positive reviews on the street and track!  The bike doesn’t feel as lazy from a dead stop anymore.  The induction noise is superb after the installation/removal and compliments the essence of what a S1000RR should sound like; a true race bike.  The IAT Kit allows for consistent power at all RPMs and gears instead of waiting for higher gears to get additional, rated power.  During our testing on the dyno and per gear / per RPM datalogging, we found many delays in the factory ignition to combat the heat soak the factory airbox flappers create.  With our flapper removal and relocated IAT sensor, the bike reacted sharp from a dead stop and in lower gears / speeds (pre-6000 RPM cruising) without knock detection.


WHAT DOES THIS KIT DO?

  • Removes factory airbox flappers to allow fresh air to enter the airbox at any speed, RPM or gear.
  • A true ambient reading means more power but also means consistent power.
  • Even distribution of air to all cylinders without any cylinder bias.
  • More air to the engine with plastic flappers removed.
  • No downside and dyno proven gains across the powerband.

WHAT'S INCLUDED?

  • (1) Flapper Servo Block-Off
  • (3) Billet Aluminum Plugs For The Airbox (Two Small and One Large)

APPLICABLE MODELS

  • 2020-2024 BMW S1000RR (2019 EU Spec)
  • 2021-2024 BMW M1000RR
  • 2023-2024 BMW BMW M1000R
  • 2019-2024 BMW S1000XR
  • 2021-2024 BMW S1000R

FLAPPER DELETE INSTALLATION VIDEO

Total install time: 1 - 1.5 hours

OUR MODE.

MODE™ Strives to push the boundaries in automotive modification, styling and tuning by creating individualised vehicles that are truly one of a kind. These days cars have become a staple in our everyday lives. No matter what we drive, there is usually some or even many more of the exact same car out there. What we drive has become more and more a reflection of ourselves and our individuality. Seeing this we created a new concept in automotive modification in Australia.Each purchase made online can be delivered directly to your door or to one of our authorised MODE™ dealers for fitting & installation service plus in store advice, software tuning, coding and personalisation to your vehicle.MODE™ is the master distributor to some of the World’s largest and most exclusive automotive brands with an extensive dealer network to ensure that no matter where you are we can deliver that signature MODE™ experience, an experience you will never forget.

WHAT'S YOUR MODE?

MODE+ Rewards

 

MODE+ Rewards Loyalty Program is a points-based program through which our valued customers (like you!) can earn and redeem points.

Need help signing up? Click here. 

By joining the points programme, you agree to be bound by these terms and conditions. MODE Auto Concepts may, in its sole discretion, alter, limit, or modify regulations and benefits, without prior notice except as expressly set out in these terms.

 

 

Terms and Conditions

  1. Your points and rewards have no cash value and may not be exchanged for cash.

  2. Under the points programme, one point will be rewarded for every $1 AUD spent on eligible purchases of products on our website. The current redemption value of the reward points is 1 point = 1 cent.

  3. All Reward Points will expire 1 year from the date they were awarded to your account, following which such unused and expired reward points will be automatically deducted from the balance of your reward points at the relevant time and you will no longer be able to access or use them.

  4. If, after you have earned reward points on a product, you later require a refund, the reward points you earned in respect of the refunded product will be deducted from your account when the products have been received by us and your payment has been refunded.

  5. Reward points are for your personal use only and cannot be transferred, brought, sold or in any way traded.

  6. You can check your points and rewards on your online account. In case of any inconsistency between the membership points reflected in your account and our internal records, the latter shall prevail.

  7. To spend reward points on our website, you must log in to your customer account before selecting the products you wish to purchase. When you enter your payment details, select how many reward points you wish to redeem from the options available.

  8. If you have applied points towards an order, and you wish to partially cancel items off the order, the reward points will be partially refunded as well for your future orders.
For more information, please contact us at store@modeautoconcepts.com